LI1BV-0L

Mini-ITX (170 x 170mm)

ntel® Celeron J6412, 2.00GHz – 2.60GHz Burst, 4-Core 4-Thread, 10W TDP

4-Core 4-Thread

1 x 260-pin Single Channel DDR4-3200 SO-DIMM up to 32GB Total

Intel® UHD Graphics for 10th Gen Intel® Processors

1 x Intel I225-V PCIe 2.5GbE
2 x Intel I225-V PCIe 2.5GbE

1 x SATA3 6Gb/s
1 x M.2 (SATA & PCIe 3.0 x2, M-key, 2242 2280 NVMe)

FINTEK F81966D

Intel fTPM 2.0 (PTT)
Onboard NUVOTON TPM v2.0

External Power Supply – the board can be powered with a +12V external power supply though a DC connector on the back panel. The rear +12V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V and the shell is GND.

Internal Power Supply – the board can alternatively be powered via the internal ATX12V 2 x 2 power connector.

Caution: There is no isolation circuitry between the external +12V DC jack and the internal 2 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V DC jack is covered if the internal 2 x 2 power connector is to be used.

1 +12V 2.5mm Diameter DC Power Jack
1 VGA Port (2560 x 1600 @60Hz)
2 USB 3.2 Gen 2 (10 Gb/s)
4 USB 2.0 Port
1 RJ45 LAN (10/100/1000/2500)
1 3.5mm Line-out Jack
1 3.5mm MIC Jack

1 +12V 2.5mm Diameter DC Power Jack
1 VGA Port (2560 x 1600 @60Hz)
2 USB 3.2 Gen 2 (10 Gb/s)
2 USB 2.0 Port
2 RJ45 LAN (10/100/1000/2500)
1 3.5mm Line-out Jack
1 3.5mm MIC Jack

1 +12V 2.5mm Diameter DC Power Jack
1 HDMI
2 USB 3.2 Gen 2 (10 Gb/s)
2 USB 2.0 Port
2 RJ45 LAN (10/100/1000/2500)
1 3.5mm Line-out Jack
1 3.5mm MIC Jack

1 SATA3 6Gb/s Connector
1 M.2 M-Key, 2242 2280 (SATA & PCIe 3.0 x2 NVMe)
1 M.2 B-key, 3042 3052 (USB for 3G/LTE Modem) with SIM Card Holder
1 M.2 E-key, 2230 (PCIe 3.0 x1/USB 2.0 for WiFi)
6 Serial Port Headers (4 * RS232, 2 * RS232/422/485)
3 USB Pin Headers for 5 additional USB 2.0 Ports
1 40-pin eDP (4096 * 2160 @ 60Hz)
1 24-bit Dual Channel LVDS/Inverter (1920 * 1080 @ 60Hz)
1 8 bit GPIO Header
1 4-pin SMBUS Header
1 4-pin Fan Header
1 9-pin Front Audio Header
1 AT/ATX Mode Jumper
1 4-pin SATA Power Output (Male)
1 4-pin +12V Alternate Power Connector

External Power Supply – the board can be powered with a +12V external power supply though a DC connector on the back panel. The rear +12V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V and the shell is GND.

Internal Power Supply – the board can alternatively be powered via the internal ATX12V 2 x 2 power connector.

Caution: There is no isolation circuitry between the external +12V DC jack and the internal 2 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V DC jack is covered if the internal 2 x 2 power connector is to be used.

Windows 10 64bit
Win 10 IoT Enterprise 64-bit
Windows 11 64bit
Win 11 IoT Enterprise 64-bit

CentOS 9
Debian 11.3
Fedora 36-1.5
OpenSUSE 15.4
FreeBSD 13.1
OPNSense 22.1.2
pfSense 2.6.0
Ubuntu 22.04